Out of Stock

ATV61HC22N4

Telemecanique - Altivar 61 drive 350hp 400/480 3ph

Current response time:

18 Minutes 39 Seconds

*Santa Clara Systems is not a Telemecanique Authorized Distributor.

Description: Altivar 61 drive 350hp 400/480 3ph
Product weight: 242.51 lb(US) (110 kg)
Range of product: Altivar 61
IP degree of protection: IP00 conforming to EN/IEC 60529IP00 conforming to EN/IEC 61800-5-1IP30 on side parts conforming to EN/IEC 60529IP30 on side parts conforming to EN/IEC 61800-5-1IP30 on the front panel conforming to EN/IEC 60529IP30 on the front panel conforming to EN/IEC 61800-5-1IP41 on upper part conforming to EN/IEC 60529IP41 on upper part conforming to EN/IEC 61800-5-1IP54 on lower part conforming to EN/IEC 60529IP54 on lower part conforming to EN/IEC 61800-5-1
Standards: EN/IEC 61800-3EN 61800-3 environments 2 category C3UL Type 1EN/IEC 61800-5-1EN 61800-3 environments 1 category C3EN 55011 class A group 2IEC 60721-3-3 class 3C2
Width: 17.32 in (440 mm)
Height: 46.85 in (1190 mm)
Depth: 14.84 in (377 mm)
Operating altitude: <= 3280.84 ft. (1000 m) without derating3280.84...9842.52 ft. (1000...3000 m) with current derating 1 % per 100 m
Tightening torque: L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 362.83 lbf.in (41 N.m) / 360 lb.inPA, PB 212.39 lbf.in (24 N.m) / 212 lb.inPC/-, PO, PA/+ 362.83 lbf.in (41 N.m) / 360 lb.inAI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 5.31 lbf.in (0.6 N.m)
Vibration resistance: 1.5 mm peak to peak (f = 3...10 Hz) conforming to EN/IEC 60068-2-60.6 gn (f = 10...200 Hz) conforming to EN/IEC 60068-2-6
Shock resistance: 4 gn 11 ms conforming to EN/IEC 60068-2-27
Electrical connection: AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5 mm² / AWG 14L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 terminal 2 x 150 mm² / 2 x 350 kcmilPA, PB terminal 120 mm² / 250 kcmilPC/-, PO, PA/+ terminal 2 x 150 mm² / 2 x 350 kcmil
Insulation resistance: > 1 mOhm at 500 V DC for 1 minute to earth
motor power kW: 200 kW 3 phasesat 380...480 V220 kW 3 phasesat 380...480 V
[Us] rated supply voltage: 380...480 V (- 15...10 %)
Relative humidity: 5...95 % without condensation conforming to IEC 60068-2-35...95 % without dripping water conforming to IEC 60068-2-3
Protection type: Drive against exceeding limit speedDrive against input phase lossDrive break on the control circuitDrive input phase breaksDrive line supply overvoltageDrive line supply undervoltageDrive overcurrent between output phases and earthDrive overheating protectionDrive overvoltages on the DC busDrive power removalDrive short-circuit between motor phasesDrive thermal protectionMotor motor phase breakMotor power removalMotor thermal protection
Response time: <= 100 ms in STO (Safe Torque Off)R1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 msR2A, R2B <= 7 ms, tolerance +/- 0.5 ms
Switching frequency: 2...8 kHz adjustable2.5...8 kHz with derating factor
Product destination: Asynchronous motorsSynchronous motors
Noise level: 66 dB conforming to 86/188/EEC
Product or component type: Variable speed drive
Supply voltage limits: 323...528 V
Dielectric strength: 3535 V DC between earth and power terminals5092 V DC between control and power terminals
Product specific application: Pumping and ventilation machine
Supply frequency: 50...60 Hz (- 5...5 %)
Electromagnetic compatibility: Conforming to IEC 61000-4-2 level 3Conforming to IEC 61000-4-11Conforming to IEC 61000-4-6 level 3Conforming to IEC 61000-4-3 level 3Conforming to IEC 61000-4-4 level 4
Component name: ATV61
Network frequency: 47.5...63 Hz
Continuous output current: 427 A at 2.5 kHz, 380 V 3 phases427 A at 2.5 kHz, 460 V 3 phases
Product certifications: CSAGOSTNOM 117ULC-TickDNV
Motor power hp: 300 hp 3 phasesat 380...480 V350 hp 3 phasesat 380...480 V
Output frequency: 0.1...500 Hz
Pollution degree: 3 conforming to EN/IEC 61800-5-13 conforming to UL 840
Speed range: 1...100 in open-loop mode, without speed feedback
Phase: 3 phases
Speed accuracy: +/- 10 % of nominal slip 0.2 Tn to Tn torque variation without speed feedback
Line current: 331 Afor 480 V 3 phases 200 kW / 300 hp357 Afor 380 V 3 phases 200 kW / 300 hp383 Afor 480 V 3 phases 220 kW / 350 hp396 Afor 380 V 3 phases 220 kW / 350 hp
Torque accuracy: +/- 15 % in open-loop mode, without speed feedback
EMC filter: Level 3 EMC filter
Transient overtorque: 130 % of nominal motor torque, +/- 10 %for 60 s
Assembly style: With heat sink
Braking torque: 30 % without braking resistor<= 125 % with braking resistor

Ambient air temperature for operation: 14...113 °F (-10...45 °C) without derating113...140 °F (45...60 °C) with derating factor
Apparent power: 235 kVAfor 380 V 3 phases 200 kW / 300 hp260.6 kVAfor 380 V 3 phases 220 kW / 350 hp
Regulation loop: Frequency PI regulator
Ambient air temperature for storage: -13...158 °F (-25...70 °C)
prospective line Isc: 50 kA 3 phases
Motor slip compensation: Not available in voltage/frequency ratio (2 or 5 points)Can be suppressedAdjustableAutomatic whatever the load
Maximum transient current: 512.4 Afor 60 s 3 phases
Local signaling: 1 LED red presence of drive voltage
Nominal switching frequency: 2.5 kHz
Output voltage: <= power supply voltage
Isolation: Between power and control terminals
Asynchronous motor control profile: Voltage/frequency ratio - Energy Saving, quadratic U/fVoltage/frequency ratio, 2 pointsVoltage/frequency ratio, 5 pointsFlux vector control without sensor, standard
Type of cable: With an IP21 or an IP31 kit: 3-strand IEC cableat 104 °F (40 °C), copper 70 °C PVCWithout mounting kit: 1-strand IEC cableat 113 °F (45 °C), copper 70 °C PVCWithout mounting kit: 1-strand IEC cableat 113 °F (45 °C), copper 90 °C XLPE/EPRWith UL Type 1 kit: 3-strand UL 508 cableat 104 °F (40 °C), copper 75 °C PVC
Synchronous motor control profile: Vector control without sensor, standard
Communication port protocol: CANopenModbus
Type of polarization: No impedance Modbus
Supply: Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <= 10 mA for overload and short-circuit protectionInternal supply 24 V DC (21...27 V), <= 200 mA for overload and short-circuit protectionExternal supply 24 V DC (19...30 V)
Option card: APOGEE FLN communication cardBACnet communication cardCC-Link communication cardController inside programmable cardDeviceNet communication cardEthernet/IP communication cardFipio communication cardI/O extension cardInterbus-S communication cardLonWorks communication cardMETASYS N2 communication cardModbus Plus communication cardModbus TCP communication cardModbus/Uni-Telway communication cardMulti-pump cardProfibus DP communication cardProfibus DP V1 communication card
Analogue input number: 2
Analogue input type: AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolution 11 bits + signAI2 software-configurable current 0...20 mA, impedance 242 Ohm, resolution 11 bitsAI2 software-configurable voltage 0...10 V DC, input voltage 24 V max, impedance 30000 Ohm, resolution 11 bits
Sampling duration: Discrete input LI6 (if configured as logic input) 2 ms, +/- 0.5 msAnalog input AI1-/Al1+ 2 ms, +/- 0.5 msAnalog input Al2 2 ms, +/- 0.5 msAnalog output AO1 2 ms, +/- 0.5 msDiscrete input LI1...LI5 2 ms, +/- 0.5 ms
Accuracy: AI1-/Al1+ +/- 0.6 % for a temperature variation 60 °CAI2 +/- 0.6 % for a temperature variation 60 °CAO1 +/- 1 % for a temperature variation 60 °C
Linearity error: AI1-/Al1+ +/- 0.15 % of maximum valueAI2 +/- 0.15 % of maximum valueAO1 +/- 0.2 %
Analogue output number: 1
Analogue output type: AO1 software-configurable current, analogue output range 0...20 mA, impedance 500 Ohm, resolution 10 bitsAO1 software-configurable logic output 10 V, <= 20 mAAO1 software-configurable voltage, analogue output range 0...10 V DC, impedance 470 Ohm, resolution 10 bits
Discrete output number: 2
Discrete output type: (R1A, R1B, R1C) configurable relay logic NO/NC, electrical durability 100000 cycles(R2A, R2B) configurable relay logic NO, electrical durability 100000 cycles
Minimum switching current: Configurable relay logic 3 mAat 24 V DC
Maximum switching current: R1, R2 on resistive load, 5 A at 30 V DC, cos phi = 1, 0 msR1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4, 7 msR1, R2 on resistive load, 5 A at 250 V AC, cos phi = 1, 0 msR1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4, 7 ms
Discrete input number: 7
Discrete input type: (LI1...LI5) programmable, 24 V DC, voltage limits <= 30 V, with level 1 PLC, impedance 3500 Ohm(LI6) switch-configurable, 24 V DC, voltage limits <= 30 V, with level 1 PLC, impedance 3500 Ohm(LI6) switch-configurable PTC probe, 0...6, impedance 1500 Ohm(PWR) safety input, 24 V DC, voltage limits <= 30 V, impedance 1500 Ohm
Discrete input logic: LI1...LI5 positive logic (source), < 5 V (state 0), > 11 V (state 1)LI1...LI5 negative logic (sink), > 16 V (state 0), < 10 V (state 1)LI6 (if configured as logic input) negative logic (sink), > 16 V (state 0), < 10 V (state 1)LI6 (if configured as logic input) positive logic (source), < 5 V (state 0), > 11 V (state 1)
Acceleration and deceleration ramps: S, U or customizedAutomatic adaptation of ramp if braking capacity exceeded, by using resistorLinear adjustable separately from 0.01 to 9000 s
Braking to standstill: By DC injection
Frequency resolution: Analog input 0.024/50 HzDisplay unit 0.1 Hz
Connector type: 1 RJ45 Modbus on front face1 RJ45 Modbus on terminalMale SUB-D 9 on RJ45 CANopen
Physical interface: 2-wire RS 485 Modbus
Transmission frame: RTU Modbus
Transmission rate: 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps CANopen4800 bps, 9600 bps, 19200 bps, 38.4 Kbps Modbus on terminal9600 bps, 19200 bps Modbus on front face
Data format: 8 bits, 1 stop, even parity Modbus on front face8 bits, odd even or no configurable parity Modbus on terminal
Number of addresses: 1...247 Modbus1...127 CANopen
Method of access: Slave CANopen
Marking: CE
Operating position: Vertical +/- 10 degree

Santa Clara Systems specializes in hard-to-find parts. Choose from our overstock inventory and save on ATV61HC22N4 . Santa Clara Systems carries 10,431 items from Telemecanique.