Out of Stock

ATV71HC13N4

Telemecanique - Variable Speed Drive

Product Summary:

Range of product: Altivar 71
IP degree of protection: IP20
Standards: EN 61800-3 environments 1 category C3
Width: 340 mm
Height: 1190 mm

Current response time:

4 Minutes 8 Seconds

*Santa Clara Systems is not a Telemecanique Authorized Distributor.

Description: Variable Speed Drive
Range of product: Altivar 71
IP degree of protection: IP20
Standards: EN 61800-3 environments 1 category C3
Width: 340 mm
Height: 1190 mm
Depth: 377 mm
Operating altitude: <= 1000 m without
Tightening torque: 0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)
Vibration resistance: 0.6 gn (f= 10…200 Hz) conforming to EN/IEC 60068-2-6
Shock resistance: 7 gn for 11 ms conforming to EN/IEC 60068-2-27
Electrical connection: Terminal, clamping capacity: 2.5 mm², AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)
Insulation resistance: > 1 mOhm 500 V DC for 1 minute to earth
motor power kW: 132 kW, 3 phases at 380...480 V
Relative humidity: 5…95 % without condensation conforming to IEC 60068-2-3
Protection type: Against exceeding limit speed: drive
Response time: <= 100 ms in STO (Safe Torque Off)
Switching frequency: 2.5...8 kHz adjustable
Product or component type: Variable speed drive
Product specific application: Complex, high-power machines
Component name: ATV71
Motor power hp: 200 hp, 3 phases at 380...480 V
Maximum motor cable length: 100 m shielded cable
Power supply voltage: 380...480 V - 15...10 %
Network number of phases: 3 phases
Line current: 192 A for 480 V 3 phases 132 kW / 200 hp
EMC filter: Integrated
Assembly style: With heat sink
Variant: Reinforced version
Apparent power: 157.3 kVA at 380 V 3 phases 132 kW / 200 hp
prospective line Isc: 35 kA for 3 phases
Nominal output current: 259 A at 2.5 kHz 380 V 3 phases 132 kW / 200 hp
Maximum transient current: 388 A for 60 s 3 phases 132 kW / 200 hp
Output frequency: 0.1…500 Hz
Nominal switching frequency: 2.5 kHz
Asynchronous motor control profile: Voltage/frequency ratio (2 or 5 points)
Type of polarization: No impedance for Modbus
Product destination: Asynchronous motors
Power supply voltage limits: 323…528 V
Power supply frequency: 50...60 Hz - 5...5 %
Power supply frequency limits: 47.5...63 Hz
Speed range: 1…100 for asynchronous motor in open-loop mode, without speed feedback
Transient overtorque: 170 % of nominal motor torque +/- 10 % for 60 s every 10 minutes
Braking torque: <= 150 % with braking or hoist resistor
Synchronous motor control profile: Vector control without speed feedback
Regulation loop: Adjustable PI regulator
Motor slip compensation: Adjustable
Diagnostic: 1 LED (red)drive voltage:
Output voltage: <= power supply voltage

Insulation: Electrical between power and control
Type of cable for mounting in an enclosure: With a NEMA Type1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC
Supply: Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 mA, protection type: overload and short-circuit protection
Analogue input number: 2
Analogue input type: AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign
Input sampling time: 2 ms +/- 0.5 ms (AI1-/Al1+) - analog input(s)
Analogue output number: 1
Analogue output type: AO1 software-configurable logic output 10 V 20 mA
Discrete output number: 2
Discrete output type: Configurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cycles
Minimum switching current: 3 mA at 24 V DC for configurable relay logic
Maximum switching current: R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4
Discrete input number: 7
Discrete input type: LI1...LI5: programmable 24 V DC with level 1 PLC, impedance: 3500 Ohm
Discrete input logic: Negative logic (sink) (LI1...LI5), > 16 V (state 0), < 10 V (state 1)
Acceleration and deceleration ramps: S, U or customized
Braking to standstill: By DC injection
Frequency resolution: Analog input: 0.024/50 Hz
Communication port protocol: CANopen
Connector type: 1 RJ45 (on front face) for Modbus
Physical interface: 2-wire RS 485 for Modbus
Transmission frame: RTU for Modbus
Transmission rate: 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
Data format: 8 bits, 1 stop, even parity for Modbus on front face
Number of addresses: 1…127 for CANopen
Method of access: Slave CANopen
Marking: CE
Operating position: Vertical +/- 10 degree
Net weight: 116 kg
Functionality: Full
Specific application: Other applications
Option card: Communication card for CC-Link
Noise level: 66 dB conforming to 86/188/EEC
Dielectric strength: 3535 V DC between earth and power terminals
Electromagnetic compatibility: 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
Product certifications: NOM 117
Pollution degree: 2 conforming to EN/IEC 61800-5-1
Ambient air temperature for operation: -10…50 °C (without)
Ambient air temperature for storage: -25…70 °C
Sustainable offer status: Green Premium product
REACh Regulation: REACh Declaration
EU RoHS Directive: Pro-active compliance (Product out of EU RoHS legal scope)
Mercury free: Yes
RoHS exemption information: Yes
China RoHS Regulation: China RoHS declaration
Environmental Disclosure: Product Environmental Profile
Circularity Profile: No need of specific recycling operations
WEEE: The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins

Santa Clara Systems specializes in hard-to-find parts. Choose from our overstock inventory and save on ATV71HC13N4 . Santa Clara Systems carries 10,643 items from Telemecanique.

We are in the process of adding data and downloadable material for this item. Please search similar items for more information related to this product.