Out of Stock

LXM05AD22N4

Telemecanique - Lexium Drive

Current response time:

8 Minutes 19 Seconds

*Santa Clara Systems is not a Telemecanique Authorized Distributor.

Description: Lexium Drive
IP degree of protection: IP20 on upper part with protective cover removed conforming to EN/IEC 60529
Operating altitude: <= 1000 m without
Tightening torque: PA/+, PBI, PBe: 1.2 N.m
Vibration resistance: 1 gn (f= 13150 Hz) conforming to EN/IEC 60068-2-6
Shock resistance: 15 gn for 11 ms conforming to EN/IEC 60028-2-27
Electrical connection: Terminal, clamping capacity: 6 mm, AWG 10 (PA/+, PBI, PBe)
Overvoltage category: III
Relative humidity: Class 3K3 (5 to 93 %) without condensation conforming to IEC 60721-3-3
Protection type: Inputs signal: against reverse polarity
Response time: <= 10 ms
Switching frequency: 8 kHz
Product or component type: Motion servo drive
Component name: LXM05A
Network number of phases: Three phase
Power supply voltage: 380...480 V - 15...10 %
Continuous output current: 7 A at 8 kHz
Nominal power: 2 kW at 4 kHz
Discrete input number: 2 safety discrete input(s)
Type of polarization: Integrated and switchable impedances for CANopen
Power supply voltage limits: 323528 V
Supply frequency: 50/60 Hz - 5...5 %
Power supply frequency limits: 47.563 Hz
Line current: 5 A at 480 V
maximum prospective line Isc: 5 kA
Inrush current: 60 A
Maximum leakage current: 30 mA
Output voltage: <= power supply voltage
Insulation: Electrical between power and control
Recommended type of cable for mounting in an enclosure: Single-strand IEC cable (temperature: 45 C) copper 70 C PVC
Discrete input type: Logic (LI1, LI2, LI3, LI4 terminals)

Sampling duration: ANA1+/ANA1-, ANA2+/ANA2-: 0.25 ms analog
Discrete input voltage: 24 V DC for logic
Discrete input logic: Negative (LI1, LI2, LI3, LI4) at State 0: > 19 V at State 1: < 9 V conforming to EN/IEC 61131-2 type 1
Discrete output number: 2
Discrete output type: Logic output(s) (LO1, LO2)24 V DC
Discrete output voltage: <= 30 V DC
Discrete output logic: Negative (LO1, LO2) conforming to EN/IEC 61131-2
Contact bounce time: 1 ms for LI1...LI4
Braking current: 50 mA
Response time on output: 1 ms (LO1, LO2) for discrete output(s)
Linearity error: < +/- 0.5 %
Analogue input type: ANA1+/ANA1-, ANA2+/ANA2- analog input: differential +/- 10 V, impedance: >= 10000 Ohm, resolution: 14 bits
Safety function: PWR protection of the machine stop and/or prevent unintended operation of the servo motor conforming to IEC/EN 61800-5-2
Communication port protocol: CANopen
Connector type: RJ45 (labelled CN4) for CANopen, CANopen Motionbus
Physical interface: 2-wire RS485 multidrop Modbus
Transmission rate: 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen, CANopen Motionbus
Data format: 8 bits, no parity, 1 or 2 stop for Modbus
Number of addresses: 1127 for CANopen, CANopen Motionbus
Communication service: 1 receive SDO + 1 transmit SDO for CANopen Motionbus
Diagnostics: Drive voltage: 1 LED (red)
Signalling function: Display of faults integrated 7-segment display terminal
Max nodes number: 31 for Modbus
Input resistance: 5 kOhm
Marking: CE
Type of cooling: Fan
Operating position: Vertical +/- 10 degree
EMC filter: Integrated
Pollution degree: 2 conforming to EN/IEC 61800-5-1
Ambient air temperature for operation: 050 C

Santa Clara Systems specializes in hard-to-find parts. Choose from our overstock inventory and save on LXM05AD22N4 . Santa Clara Systems carries 10,300 items from Telemecanique.

We are in the process of adding data and downloadable material for this item. Please search similar items for more information related to this product.