ATV320U15N4C

Telemecanique - variable speed drive ATV320 - 1.5kW - 380...500V - 3 phase - compact

Current response time:

6 Minutes 50 Seconds

*Santa Clara Systems is not a Telemecanique Authorized Distributor.

Description: variable speed drive ATV320 - 1.5kW - 380...500V - 3 phase - compact
Product weight: 2.87 lb(US) (1.3 kg)
Range of product: Altivar Machine ATV320
IP degree of protection: IP20 conforming to EN/IEC 61800-5-1
Standards: EN/IEC 61800-3EN/IEC 61800-3 environment 1 category C2EN/IEC 61800-5-1IEC 60721-3IEC 61508IEC 13849-1
Device short name: ATV320
Width: 4.13 in (105 mm)
Height: 142 mm188 mm with EMC plate
Depth: 6.22 in (158 mm)
Operating altitude: <= 3280.84 ft. (1000 m) without derating3280.84...9842.52 ft. (1000...3000 m) with current derating 1 % per 100 m
Vibration resistance: 1.5 mm peak to peak (f = 2...13 Hz) conforming to EN/IEC 60068-2-61 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6
Shock resistance: 15 gn during 11 ms conforming to EN/IEC 60068-2-27
Electrical connection: Control, screw terminal: 0.5...1.5 mm² AWG 20...AWG 16Motor/braking resistor, screw terminal: 2.5...6 mm² AWG 14...AWG 10Power supply, screw terminal: 2.5...6 mm² AWG 14...AWG 10
Insulation resistance: > 1 mOhm at 500 V DC for 1 minute to earth
motor power kW: 1.5 kW heavy duty
[Us] rated supply voltage: 380...500 V (- 15...10 %)
Relative humidity: 5...95 % without condensation conforming to IEC 60068-2-35...95 % without dripping water conforming to IEC 60068-2-3
Protection type: Drive: thermal protectionDrive: overcurrent between output phases and earthDrive: input phase breaksDrive: overheating protectionDrive: short-circuit between motor phases
Switching frequency: 4...16 kHz with current derating2...16 kHz adjustable
Degree of protection: UL type 1 with UL type 1 conformity kit
Output voltage: <= power supply voltage
Isolation: Between power and control terminals
Product or component type: Variable speed drive
Permissible temporary current boost: 1.5 x In during 60 s heavy duty
Product specific application: Complex machines
Speed range: 1...100 with asynchronous motor in open-loop mode
Noise level: 51 dB conforming to 86/188/EEC
Speed accuracy: +/- 10 % of nominal slip 0.2 Tn to Tn
power dissipation in W: 61 W (fan) at 380 V, 4 kHz
Format of the drive: Compact
Torque accuracy: +/- 15 %
Volume of cooling air: 4755.18 Gal/hr(US) (18 m3/h)
Product destination: Asynchronous motorsSynchronous motors
Transient overtorque: 170...200 % of nominal motor torque
Operating position: Vertical +/- 10 degree
EMC filter: Class C2 EMC filter integrated
Braking torque: <= 170 % with braking resistor during 60 s
Electromagnetic compatibility: Conducted radio-frequency immunity test conforming to IEC 61000-4-6 level 3Electrical fast transient/burst immunity test conforming to IEC 61000-4-4 level 4Electrostatic discharge immunity test conforming to IEC 61000-4-2 level 3Radiated radio-frequency electromagnetic field immunity test conforming to IEC 61000-4-3 level 3Voltage dips and interruptions immunity test conforming to IEC 61000-4-111.2/50 µs - 8/20 µs surge immunity test conforming to IEC 61000-4-5 level 3
Regulation loop: Adjustable PID regulator
Pollution degree: 2 conforming to EN/IEC 61800-5-1
Motor slip compensation: Adjustable 0...300 %Not available in voltage/frequency ratio (2 or 5 points)Automatic whatever the load
Type of cooling: Fan
Acceleration and deceleration ramps: UDeceleration ramp automatic stop DC injectionDeceleration ramp adaptationRamp switchingLinearCUSS
Phase: 3 phases
Braking to standstill: By DC injection
Ambient air temperature for operation: 14...122 °F (-10...50 °C) without derating122...140 °F (50...60 °C) with derating factor
Supply frequency: 50...60 Hz (- 5...5 %)

Frequency resolution: Display unit: 0.1 HzAnalog input: 0.012/50 Hz
Ambient air temperature for storage: -13...158 °F (-25...70 °C)
Motor power hp: 2 hp heavy duty
Connector type: 1 RJ45 Modbus/CANopen on control terminal
Line current: 6.4 A at 380 V heavy duty4.9 A at 500 V heavy duty
Physical interface: 2-wire RS 485 Modbus
Product certifications: RCMULEACCSANOM 117
prospective line Isc: <= 5 kA
Transmission frame: RTU Modbus
Marking: CE
Apparent power: 4.2 kVA at 500 V heavy duty
Transmission rate: 4.8, 9.6, 19.2, 38.4 kbit/s Modbus50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps CANopen
Continuous output current: 4.1 A at 4 kHz heavy duty
Data format: 8 bits, configurable odd, even or no parity Modbus
Maximum transient current: 6.2 A during 60 s heavy duty
Type of polarization: No impedance Modbus
Asynchronous motor control profile: Voltage/frequency ratio - Energy Saving, quadratic U/fFlux vector control without sensor, standardVoltage/frequency ratio, 2 pointsFlux vector control without sensor - Energy SavingVoltage/frequency ratio, 5 points
Number of addresses: 1...247 Modbus1...127 CANopen
Synchronous motor control profile: Vector control without sensor
Method of access: Slave CANopen
Speed drive output frequency: 0.1...599 Hz
Supply: Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC (+/- 5 %) current <= 10 mA (overload and short-circuit protection)
Nominal switching frequency: 4 kHz
Local signaling: 1 LED green CANopen run1 LED red CANopen error1 LED red drive fault
Safety function: STO (safe torque off) SIL 3SS1 (safe stop 1)SMS (safe maximum speed)SLS (safe limited speed)GDL (guard door locking)
Communication port protocol: CANopenModbus
Option card: Communication module: CANopen daisy chain RJ45Communication module: CANopen SUB-D 9Communication module: CANopen open style terminal blockCommunication module: EtherCAT RJ45Communication module: DeviceNetCommunication module: Ethernet/IPCommunication module: Profibus DP V1Communication module: ProfinetCommunication module: Ethernet Powerlink
Analogue input number: 3
Analogue input type: Voltage (AI1): 0...10 V DC, impedance 30000 Ohm, resolution 10 bitsBipolar differential voltage (AI2): +/- 10 V DC, impedance 30000 Ohm, resolution 10 bitsCurrent (AI3): 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration), impedance 250 Ohm, resolution 10 bits
Discrete input number: 7
Discrete input type: Programmable (sink/source) (DI1...DI4): 24...30 V DC: level 1 PLCProgrammable as pulse input 20 kpps (DI5): 24...30 V DC: level 1 PLCSwitch-configurable PTC probe (DI6): 24...30 V DCSafe torque off (STO): 24...30 V DC, impedance 1500 Ohm
Discrete input logic: Negative logic (sink): : DI1...DI6, > 19 V (state 0) < 13 V (state 1)Positive logic (source): : DI1...DI6, < 5 V (state 0) > 11 V (state 1)
Analogue output number: 1
Analogue output type: Software-configurable current (AQ1): 0...20 mA, impedance 800 Ohm, resolution 10 bitsSoftware-configurable voltage (AQ1): 0...10 V, impedance 470 Ohm, resolution 10 bits
Sampling duration: Analog input (AI1, AI2, AI3): 2 msAnalog output (AQ1): 2 ms
Accuracy: Analog input AI1, AI2, AI3: +/- 0.2 % for a temperature of -10...60 °CAnalog input AI1, AI2, AI3: +/- 0.5 % for a temperature of 25 °CAnalog output AQ1: +/- 1 % for a temperature of 25 °CAnalog output AQ1: +/- 2 % for a temperature of -10...60 °C
Linearity error: Analog input (AI1, AI2, AI3): +/- 0.2...0.5 % of maximum valueAnalog output (AQ1): +/- 0.3 %
Discrete output number: 3
Discrete output type: Configurable relay logic NO/NC (R1A, R1B, R1C): electrical durability 100000 cyclesConfigurable relay logic NO (R2A, R2B): electrical durability 100000 cyclesLogic (LO)
Refresh time: Logic input (DI1...DI6): 8 ms (+/- 0.7 ms)Relay output (R1A, R1B, R1C): 2 msRelay output (R2A, R2C): 2 ms
Minimum switching current: Relay output (R1, R2): 5 mA at 24 V DC
Maximum switching current: Relay output (R1) on resistive load (cos phi = 1: 3 A at 250 V ACRelay output (R1) on resistive load (cos phi = 1: 4 A at 30 V DCRelay output (R1, R2) on inductive load (cos phi = 0.4: 2 A at 250 V ACRelay output (R1, R2) on inductive load (cos phi = 0.4: 2 A at 30 V DCRelay output (R2) on resistive load (cos phi = 1: 5 A at 250 V ACRelay output (R2) on resistive load (cos phi = 1: 5 A at 30 V DC
Specific application: Machinery
Discrete and process manufacturing: Hoisting self erectingMaterial handling carouselMaterial handling conveyorMaterial handling lifting platfromMaterial handling palletizers - medium performanceMaterial handling transfer tableMaterial handling turn tableMaterial working (wood, ceramic, stone, pvc, metal) cutting - medium accuracyMaterial working (wood, ceramic, stone, pvc, metal) drillingMaterial working (wood, ceramic, stone, pvc, metal) sawPackaging baggingPackaging feed conveyor low performancePackaging filling bottles - intermittent operationPackaging linear labelingPackaging other applicationPackaging stretching wrappingPackaging tray takeTextile knittingTextile printing machinesTextile spinningWashing machines carWashing machines other applicationHoisting standard crane - travelling or trolley
Power range: 1.1...2 kW 380...440 V 3 phases1.1...2 kW 480...500 V 3 phases
Motor starter type: Variable speed drive

Santa Clara Systems specializes in hard-to-find parts. Choose from our overstock inventory and save on ATV320U15N4C . Santa Clara Systems carries 10,431 items from Telemecanique.